firmware/batmon.c

@@ -1,18 +1,11 @@
 #include <avr/io.h>
 #include "batmon.h"
-#include "systick.h"
-
-static uint8_t vbat = 0;
 
 void batmon_init()
 {
-	TCCR0A = 0;
-	TCCR0B = (1 << CS02);
-	TIMSK0 = (1 << TOIE0);
-
 	ADCSRA = (1 << ADPS2) | (1 << ADPS1); // 125 kHz ADC clock
 	ADMUX = ADC_CHANNEL | (1 << REFS0) | (1 << REFS1) | (1 << ADLAR); // Internal 1.2V bandgap, left adj.
-	ADCSRB = 0;
+	ADCSRB = 0; // Manual start
 #if ADC_CHANNEL < 7
 	DIDR0 = (1 << ADC_CHANNEL); // Disconnect digital channel
 #endif
@@ -23,30 +16,10 @@ void batmon_init()
 
 	// Enable ADC
 	ADCSRA |= (1 << ADEN);
-	ADCSRA |= (1 << ADSC);
-}
-
-uint8_t batmon_proc()
-{
-	static uint16_t sum = 0;
-	static uint8_t cnt = 0;
-
-	if (ADCSRA & (1 << ADIF)) {
-		sum += ADCH;
-		if (!(cnt++)) {
-			vbat = sum >> 8;
-			sum = 0;
-		}
-		vbat = ADCH;
-		ADCSRA &= ~(1 << ADIF);
-		ADCSRA |= (1 << ADSC); // TODO: I want this to work off TIMER0
-		if (vbat < BAT_THRES_POWER_OFF)
-			return 1;
-	}
-	return 0;
 }
 
 inline uint8_t batmon_get_voltage()
 {
-	return vbat;
+	ADCSRA |= (1 << ADSC); // TODO: Check whether this increases the power consumption of the chip by much
+	return ADCH;
 }

firmware/batmon.h

@@ -6,11 +6,7 @@
 #define PORT_ADCC(t) t##D
 #define PIN_ADCC (1 << 1)
 
-#define BAT_THRES_POWER_ON 60 // TODO: Minimum ADC value to allow turning the device on
-#define BAT_THRES_POWER_OFF 50 // TODO: ADC value to (hard) power off the device.
-
 void batmon_init();
 uint8_t batmon_get_voltage();
-uint8_t batmon_proc();
 
 #endif // BATMON_H

firmware/input.c

@@ -21,16 +21,13 @@ inline int8_t get_rotary_delta()
 	return rotary_delta;
 }
 
-#define ROTARY_DEBOUNCE 150
 static inline void input_proc_rotary()
 {
 	static int8_t last_a;
 	int8_t a;
 	int8_t b;
 	int8_t p;
-	uint8_t silly_debounce = 0;
 
-	if (silly_debounce == 0) {
 	p = PORT_ROTARY(PIN);
 	a = (p & PIN_ROTARY_A);
 	b = (p & PIN_ROTARY_B);
@@ -38,18 +35,15 @@ static inline void input_proc_rotary()
 	b = !b;
 
 	if (a == 1 && last_a == 0) {
-			silly_debounce = ROTARY_DEBOUNCE;
+		_delay_ms(1); // TODO
 		rotary_delta += !!(a ^ b);
 	}
 	if (a == 0 && last_a == 1) {
-			silly_debounce = ROTARY_DEBOUNCE;
+		_delay_ms(1); // TODO
 		rotary_delta -= !(a ^ b);
 	}
 
 	last_a = a;
-	} else {
-		silly_debounce--;
-	}
 }
 
 // TODO: Pressing two keys at the same time can lead to unfortunate behavior.
@@ -59,6 +53,7 @@ void input_proc_switches()
 	uint8_t ev;
 	uint8_t i;
 	static uint8_t sw_last = 0xFF;
+	uint8_t delta;
 
 	sw = PORT_KEYPAD(PIN) & PIN_KEYPAD_MASK;
 	ev = sw ^ sw_last;

firmware/main.c

@@ -83,7 +83,6 @@ void lcd_title(const char *msg1, const char *msg2)
 int main()
 {
 	char *post_msg;
-	uint8_t sched = 0;
 
 	MCUSR &= ~(1 << WDRF);
 	WDTCSR = (1 << WDCE);
@@ -109,20 +108,8 @@ int main()
 
 	while (1) {
 		if (!spi_proc()) {
-			switch (sched) {
-			case 0:
 			timer_proc();
-				break;
-			case 1:
 			input_proc();
-				break;
-			}
-		}
-		sched = sched + 1;
-		if (sched == 4) {
-			sched = 0;
-			if (batmon_proc())
-				reset();
 		}
 	}
 	return 0;

firmware/pm.h

@@ -3,6 +3,5 @@
 #include <avr/io.h>
 
 void suspend();
-char* post();
 
 #endif // PM_H