ioc: bootloader: Disable LED, add X and Z commands, clean up

This commit is contained in:
Markus Koch 2019-11-10 19:48:24 +01:00
parent 1be8f62f3e
commit b4bc651445
3 changed files with 232 additions and 297 deletions

3
.gitignore vendored
View File

@ -1,6 +1,3 @@
# Directories
doc
# AVR temp files
*.srec
*.s

11
doc/ioc.md Normal file
View File

@ -0,0 +1,11 @@
# IOC
## Firmware
### General
* All serial links run at 19200 baud
### Bootloader
* The bootloader is a standard Arduino bootloader with the following additions
* Use ASCII command 'X' to enable loop-through mode. Everything received on UART RX will be forwarded to UART TX until the next reset.
* Use ASCII command 'Z' to immediately launch into the user firmware
* Use the following avrdude command to program: `avrdude -p m8 -P /dev/ttyUSBx -c arduino -b 19200 -U flash:w:$(TARGET).hex`

View File

@ -7,6 +7,7 @@
/* */
/* Hacked by DojoCorp - ZGZ - MMX - IVR */
/* Hacked by David A. Mellis */
/* Hacked by Markus Koch */
/* */
/* This program is free software; you can redistribute it */
/* and/or modify it under the terms of the GNU General */
@ -38,19 +39,7 @@
#include <avr/interrupt.h>
#include <util/delay.h>
//#define F_CPU 16000000
/* We, Malmoitians, like slow interaction
* therefore the slow baud rate ;-)
*/
//#define BAUD_RATE 9600
/* 6.000.000 is more or less 8 seconds at the
* speed configured here
*/
//#define MAX_TIME_COUNT 6000000
#define MAX_TIME_COUNT (F_CPU>>1)
///#define MAX_TIME_COUNT_MORATORY 1600000
/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */
#define HW_VER 0x02
@ -61,18 +50,18 @@
// avr-gcc compiler v3.1.x and older doesn't support outb() and inb()
// if necessary, convert outb and inb to outp and inp
#ifndef outb
#define outb(sfr,val) (_SFR_BYTE(sfr) = (val))
#define outb(sfr,val) (_SFR_BYTE(sfr) = (val))
#endif
#ifndef inb
#define inb(sfr) _SFR_BYTE(sfr)
#define inb(sfr) _SFR_BYTE(sfr)
#endif
/* defines for future compatibility */
#ifndef cbi
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
#endif
#ifndef sbi
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
#endif
/* Adjust to suit whatever pin your hardware uses to enter the bootloader */
@ -80,12 +69,6 @@
#define eeprom_rw(addr) eeprom_read_word ((uint16_t *)(addr))
#define eeprom_wb(addr, val) eeprom_write_byte ((uint8_t *)(addr), (uint8_t)(val))
/* Onboard LED is connected to pin PB5 */
#define LED_DDR DDRB
#define LED_PORT PORTB
#define LED_PIN PINB
#define LED PINB5
#define SIG1 0x1E // Yep, Atmel is the only manufacturer of AVR micros. Single source :(
#define SIG2 0x93
@ -100,18 +83,18 @@ void byte_response(uint8_t);
void nothing_response(void);
union address_union {
uint16_t word;
uint8_t byte[2];
uint16_t word;
uint8_t byte[2];
} address;
union length_union {
uint16_t word;
uint8_t byte[2];
uint16_t word;
uint8_t byte[2];
} length;
struct flags_struct {
unsigned eeprom : 1;
unsigned rampz : 1;
unsigned eeprom : 1;
unsigned rampz : 1;
} flags;
uint8_t buff[256];
@ -127,81 +110,50 @@ void (*app_start)(void) = 0x0000;
int main(void)
{
uint8_t ch,ch2;
uint16_t w;
uint8_t ch,ch2;
uint16_t w;
//cbi(BL_DDR,BL);
//sbi(BL_PORT,BL);
/* Disable interrupts */
cli();
asm volatile("nop\n\t");
/* Pre-init I/O */
DDRB = 0;
DDRC = 0;
DDRD = 0;
PORTB = 0;
PORTC = 0;
PORTD = 0;
/* check if flash is programmed already, if not start bootloader anyway */
//if(pgm_read_byte_near(0x0000) != 0xFF) {
asm volatile("nop\n\t");
/* check if bootloader pin is set low */
//if(bit_is_set(BL_PIN,BL)) app_start();
//}
/* initialize UART(s) depending on CPU defined */
/* m8 */
UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; // set baud rate
UBRRL = (((F_CPU/BAUD_RATE)/16)-1);
UCSRB = (1<<RXEN)|(1<<TXEN); // enable Rx & Tx
UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0); // config USART; 8N1
/* initialize UART(s) depending on CPU defined */
/* m8 */
UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; // set baud rate
UBRRL = (((F_CPU/BAUD_RATE)/16)-1);
UCSRB = (1<<RXEN)|(1<<TXEN); // enable Rx & Tx
UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0); // config USART; 8N1
//UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
//UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
//UCSRA = 0x00;
//UCSRC = 0x86;
//UCSRB = _BV(TXEN)|_BV(RXEN);
/* this was giving uisp problems, so I removed it; without it, the boot
works on with uisp and avrdude on the mac (at least). */
//putch('\0');
//uint32_t l;
//uint32_t time_count;
//time_count=0;
/* set LED pin as output */
sbi(LED_DDR,LED);
for (i = 0; i < 16; i++) {
outb(LED_PORT, inb(LED_PORT) ^ _BV(LED));
_delay_loop_2(0);
}
//for (l=0; l<40000000; l++)
//outb(LED_PORT, inb(LED_PORT) ^= _BV(LED));
/* flash onboard LED three times to signal entering of bootloader */
//for(i=0; i<3; ++i) {
//for(l=0; l<40000000; ++l);
//sbi(LED_PORT,LED);
//for(l=0; l<40000000; ++l);
//cbi(LED_PORT,LED);
//}
/* see comment at previous call to putch() */
//putch('\0'); // this line is needed for the synchronization of the programmer
/* forever */
for (;;) {
//if((inb(UCSRA) & _BV(RXC))){
/* get character from UART */
/* forever */
for (;;) {
//if ((inb(UCSRA) & _BV(RXC))){
/* get character from UART */
ch = getch();
/* A bunch of if...else if... gives smaller code than switch...case ! */
/* Hello is anyone home ? */
if(ch=='0') {
nothing_response();
/* Hello is anyone home ? */
if (ch == '0') {
nothing_response();
}
/* Request programmer ID */
/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry */
/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares. */
else if(ch=='1') {
else if (ch == '1') {
if (getch() == ' ') {
putch(0x14);
putch('A');
@ -212,296 +164,271 @@ int main(void)
putch('S');
putch('P');
putch(0x10);
}
}
}
/* AVR ISP/STK500 board commands DON'T CARE so default nothing_response */
else if(ch=='@') {
ch2 = getch();
if (ch2>0x85) getch();
nothing_response();
else if (ch == '@') {
ch2 = getch();
if (ch2>0x85) getch();
nothing_response();
}
/* AVR ISP/STK500 board requests */
else if(ch=='A') {
ch2 = getch();
if(ch2==0x80) byte_response(HW_VER); // Hardware version
else if(ch2==0x81) byte_response(SW_MAJOR); // Software major version
else if(ch2==0x82) byte_response(SW_MINOR); // Software minor version
//else if(ch2==0x98) byte_response(0x03); // Unknown but seems to be required by avr studio 3.56
else byte_response(0x00); // Covers various unnecessary responses we don't care about
else if (ch == 'A') {
ch2 = getch();
if (ch2==0x80) byte_response(HW_VER); // Hardware version
else if (ch2==0x81) byte_response(SW_MAJOR); // Software major version
else if (ch2==0x82) byte_response(SW_MINOR); // Software minor version
//else if (ch2==0x98) byte_response(0x03); // Unknown but seems to be required by avr studio 3.56
else byte_response(0x00); // Covers various unnecessary responses we don't care about
}
/* Device Parameters DON'T CARE, DEVICE IS FIXED */
else if(ch=='B') {
getNch(20);
nothing_response();
else if (ch == 'B') {
getNch(20);
nothing_response();
}
/* Parallel programming stuff DON'T CARE */
else if(ch=='E') {
getNch(5);
nothing_response();
else if (ch == 'E') {
getNch(5);
nothing_response();
}
/* Enter programming mode */
else if(ch=='P') {
nothing_response();
// FIXME: modified only here by DojoCorp, Mumbai, India, 20050626
//time_count=0; // exted the delay once entered prog.mode
else if (ch == 'P') {
nothing_response();
// FIXME: modified only here by DojoCorp, Mumbai, India, 20050626
//time_count=0; // exted the delay once entered prog.mode
}
/* Leave programming mode */
else if(ch=='Q') {
nothing_response();
//time_count=MAX_TIME_COUNT_MORATORY; // once the programming is done,
// we should start the application
// but uisp has problems with this,
// therefore we just change the times
// and give the programmer 1 sec to react
else if (ch == 'Q') {
nothing_response();
//time_count=MAX_TIME_COUNT_MORATORY; // once the programming is done,
// we should start the application
// but uisp has problems with this,
// therefore we just change the times
// and give the programmer 1 sec to react
}
/* Loop UART until reset */
else if (ch == 'X') {
while (1) {
if (UCSRA & (1 << RXC)) {
UDR = UDR;
}
}
}
/* Start user code NOW */
else if (ch == 'Z') {
app_start();
}
/* Erase device, don't care as we will erase one page at a time anyway. */
else if(ch=='R') {
nothing_response();
else if (ch == 'R') {
nothing_response();
}
/* Set address, little endian. EEPROM in bytes, FLASH in words */
/* Perhaps extra address bytes may be added in future to support > 128kB FLASH. */
/* This might explain why little endian was used here, big endian used everywhere else. */
else if(ch=='U') {
address.byte[0] = getch();
address.byte[1] = getch();
nothing_response();
else if (ch == 'U') {
address.byte[0] = getch();
address.byte[1] = getch();
nothing_response();
}
/* Universal SPI programming command, disabled. Would be used for fuses and lock bits. */
else if(ch=='V') {
getNch(4);
byte_response(0x00);
else if (ch == 'V') {
getNch(4);
byte_response(0x00);
}
/* Write memory, length is big endian and is in bytes */
else if(ch=='d') {
length.byte[1] = getch();
length.byte[0] = getch();
flags.eeprom = 0;
if (getch() == 'E') flags.eeprom = 1;
for (w=0;w<length.word;w++) {
buff[w] = getch(); // Store data in buffer, can't keep up with serial data stream whilst programming pages
}
if (getch() == ' ') {
else if (ch == 'd') {
length.byte[1] = getch();
length.byte[0] = getch();
flags.eeprom = 0;
if (getch() == 'E') flags.eeprom = 1;
for (w=0; w<length.word; w++) {
buff[w] = getch(); // Store data in buffer, can't keep up with serial data stream whilst programming pages
}
if (getch() == ' ') {
if (flags.eeprom) { //Write to EEPROM one byte at a time
for(w=0;w<length.word;w++) {
eeprom_wb(address.word,buff[w]);
address.word++;
}
}
} else { //Write to FLASH one page at a time
//if (address.byte[1]>127) address_high = 0x01; //Only possible with m128, m256 will need 3rd address byte. FIXME
//else address_high = 0x00;
//address.word = address.word << 1; //address * 2 -> byte location
//if ((length.byte[0] & 0x01)) length.word++; //Even up an odd number of bytes
cli(); //Disable interrupts, just to be sure
while(bit_is_set(EECR,EEWE)); //Wait for previous EEPROM writes to complete
asm volatile(
"clr r17 \n\t" //page_word_count
"lds r30,address \n\t" //Address of FLASH location (in words)
"lds r31,address+1 \n\t"
"lsl r30 \n\t" //address * 2 -> byte location
"rol r31 \n\t"
"ldi r28,lo8(buff) \n\t" //Start of buffer array in RAM
"ldi r29,hi8(buff) \n\t"
"lds r24,length \n\t" //Length of data to be written (in bytes)
"lds r25,length+1 \n\t"
"sbrs r24,0 \n\t" //Even up an odd number of bytes
"rjmp length_loop \n\t"
"adiw r24,1 \n\t"
"length_loop: \n\t" //Main loop, repeat for number of words in block
"cpi r17,0x00 \n\t" //If page_word_count=0 then erase page
"brne no_page_erase \n\t"
"rcall wait_spm \n\t"
// "wait_spm1: \n\t"
// "lds r16,%0 \n\t" //Wait for previous spm to complete
// "andi r16,1 \n\t"
// "cpi r16,1 \n\t"
// "breq wait_spm1 \n\t"
"ldi r16,0x03 \n\t" //Erase page pointed to by Z
"sts %0,r16 \n\t"
"spm \n\t"
"rcall wait_spm \n\t"
// "wait_spm2: \n\t"
// "lds r16,%0 \n\t" //Wait for previous spm to complete
// "andi r16,1 \n\t"
// "cpi r16,1 \n\t"
// "breq wait_spm2 \n\t"
"ldi r16,0x11 \n\t" //Re-enable RWW section
"sts %0,r16 \n\t"
"spm \n\t"
"no_page_erase: \n\t"
"ld r0,Y+ \n\t" //Write 2 bytes into page buffer
"ld r1,Y+ \n\t"
"rcall wait_spm \n\t"
// "wait_spm3: \n\t"
// "lds r16,%0 \n\t" //Wait for previous spm to complete
// "andi r16,1 \n\t"
// "cpi r16,1 \n\t"
// "breq wait_spm3 \n\t"
"ldi r16,0x01 \n\t" //Load r0,r1 into FLASH page buffer
"sts %0,r16 \n\t"
"spm \n\t"
"inc r17 \n\t" //page_word_count++
"cpi r17,%1 \n\t"
"brlo same_page \n\t" //Still same page in FLASH
"write_page: \n\t"
"clr r17 \n\t" //New page, write current one first
"rcall wait_spm \n\t"
// "wait_spm4: \n\t"
// "lds r16,%0 \n\t" //Wait for previous spm to complete
// "andi r16,1 \n\t"
// "cpi r16,1 \n\t"
// "breq wait_spm4 \n\t"
"ldi r16,0x05 \n\t" //Write page pointed to by Z
"sts %0,r16 \n\t"
"spm \n\t"
"rcall wait_spm \n\t"
// "wait_spm5: \n\t"
// "lds r16,%0 \n\t" //Wait for previous spm to complete
// "andi r16,1 \n\t"
// "cpi r16,1 \n\t"
// "breq wait_spm5 \n\t"
"ldi r16,0x11 \n\t" //Re-enable RWW section
"sts %0,r16 \n\t"
"spm \n\t"
"same_page: \n\t"
"adiw r30,2 \n\t" //Next word in FLASH
"sbiw r24,2 \n\t" //length-2
"breq final_write \n\t" //Finished
"rjmp length_loop \n\t"
"wait_spm: \n\t"
"lds r16,%0 \n\t" //Wait for previous spm to complete
"andi r16,1 \n\t"
"cpi r16,1 \n\t"
"breq wait_spm \n\t"
"ret \n\t"
"final_write: \n\t"
"cpi r17,0 \n\t"
"breq block_done \n\t"
"adiw r24,2 \n\t" //length+2, fool above check on length after short page write
"rjmp write_page \n\t"
"block_done: \n\t"
"clr __zero_reg__ \n\t" //restore zero register
: "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31");
"clr r17 \n\t" //page_word_count
"lds r30,address \n\t" //Address of FLASH location (in words)
"lds r31,address+1 \n\t"
"lsl r30 \n\t" //address * 2 -> byte location
"rol r31 \n\t"
"ldi r28,lo8(buff) \n\t" //Start of buffer array in RAM
"ldi r29,hi8(buff) \n\t"
"lds r24,length \n\t" //Length of data to be written (in bytes)
"lds r25,length+1 \n\t"
"sbrs r24,0 \n\t" //Even up an odd number of bytes
"rjmp length_loop \n\t"
"adiw r24,1 \n\t"
"length_loop: \n\t" //Main loop, repeat for number of words in block
"cpi r17,0x00 \n\t" //If page_word_count=0 then erase page
"brne no_page_erase \n\t"
"rcall wait_spm \n\t"
"ldi r16,0x03 \n\t" //Erase page pointed to by Z
"sts %0,r16 \n\t"
"spm \n\t"
"rcall wait_spm \n\t"
"ldi r16,0x11 \n\t" //Re-enable RWW section
"sts %0,r16 \n\t"
"spm \n\t"
"no_page_erase: \n\t"
"ld r0,Y+ \n\t" //Write 2 bytes into page buffer
"ld r1,Y+ \n\t"
"rcall wait_spm \n\t"
"ldi r16,0x01 \n\t" //Load r0,r1 into FLASH page buffer
"sts %0,r16 \n\t"
"spm \n\t"
"inc r17 \n\t" //page_word_count++
"cpi r17,%1 \n\t"
"brlo same_page \n\t" //Still same page in FLASH
"write_page: \n\t"
"clr r17 \n\t" //New page, write current one first
"rcall wait_spm \n\t"
"ldi r16,0x05 \n\t" //Write page pointed to by Z
"sts %0,r16 \n\t"
"spm \n\t"
"rcall wait_spm \n\t"
"ldi r16,0x11 \n\t" //Re-enable RWW section
"sts %0,r16 \n\t"
"spm \n\t"
"same_page: \n\t"
"adiw r30,2 \n\t" //Next word in FLASH
"sbiw r24,2 \n\t" //length-2
"breq final_write \n\t" //Finished
"rjmp length_loop \n\t"
"wait_spm: \n\t"
"lds r16,%0 \n\t" //Wait for previous spm to complete
"andi r16,1 \n\t"
"cpi r16,1 \n\t"
"breq wait_spm \n\t"
"ret \n\t"
"final_write: \n\t"
"cpi r17,0 \n\t"
"breq block_done \n\t"
"adiw r24,2 \n\t" //length+2, fool above check on length after short page write
"rjmp write_page \n\t"
"block_done: \n\t"
"clr __zero_reg__ \n\t" //restore zero register
: "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31");
/* Should really add a wait for RWW section to be enabled, don't actually need it since we never */
/* exit the bootloader without a power cycle anyhow */
}
putch(0x14);
putch(0x10);
}
}
}
/* Read memory block mode, length is big endian. */
else if(ch=='t') {
length.byte[1] = getch();
length.byte[0] = getch();
if (getch() == 'E') flags.eeprom = 1;
else {
else if (ch == 't') {
length.byte[1] = getch();
length.byte[0] = getch();
if (getch() == 'E') flags.eeprom = 1;
else {
flags.eeprom = 0;
address.word = address.word << 1; // address * 2 -> byte location
}
if (getch() == ' ') { // Command terminator
}
if (getch() == ' ') { // Command terminator
putch(0x14);
for (w=0;w < length.word;w++) { // Can handle odd and even lengths okay
for (w=0; w < length.word; w++) { // Can handle odd and even lengths okay
if (flags.eeprom) { // Byte access EEPROM read
putch(eeprom_rb(address.word));
address.word++;
} else {
} else {
if (!flags.rampz) putch(pgm_read_byte_near(address.word));
address.word++;
}
}
putch(0x10);
}
}
}
/* Get device signature bytes */
else if(ch=='u') {
if (getch() == ' ') {
else if (ch == 'u') {
if (getch() == ' ') {
putch(0x14);
putch(SIG1);
putch(SIG2);
putch(SIG3);
putch(0x10);
}
}
}
/* Read oscillator calibration byte */
else if(ch=='v') {
byte_response(0x00);
else if (ch == 'v') {
byte_response(0x00);
}
// } else {
// time_count++;
// if (time_count>=MAX_TIME_COUNT) {
// app_start();
// }
// }
} /* end of forever loop */
}
void putch(char ch)
{
/* m8 */
while (!(inb(UCSRA) & _BV(UDRE)));
outb(UDR,ch);
/* m8 */
while (!(inb(UCSRA) & _BV(UDRE)));
outb(UDR,ch);
}
char getch(void)
{
/* m8 */
/* m8 */
uint32_t count = 0;
while(!(inb(UCSRA) & _BV(RXC))) {
while(!(inb(UCSRA) & _BV(RXC))) {
/* HACKME:: here is a good place to count times*/
count++;
if (count > MAX_TIME_COUNT)
app_start();
}
return (inb(UDR));
}
return (inb(UDR));
}
void getNch(uint8_t count)
{
uint8_t i;
for(i=0;i<count;i++) {
/* m8 */
//while(!(inb(UCSRA) & _BV(RXC)));
//inb(UDR);
uint8_t i;
for(i=0;i<count;i++) {
getch(); // need to handle time out
}
}
}
void byte_response(uint8_t val)
{
if (getch() == ' ') {
putch(0x14);
putch(val);
putch(0x10);
}
if (getch() == ' ') {
putch(0x14);
putch(val);
putch(0x10);
}
}
void nothing_response(void)
{
if (getch() == ' ') {
putch(0x14);
putch(0x10);
}
if (getch() == ' ') {
putch(0x14);
putch(0x10);
}
}
/* end of file ATmegaBOOT.c */