doc/lit.bib

@@ -43,13 +43,3 @@
   Timestamp                = {2017.11.10},
   Url                      = {http://www.latticesemi.com/~/media/LatticeSemi/Documents/DataSheets/MachXO23/MachXO2FamilyDataSheet.pdf?document_id=38834}
 }
-
-@Manual{ioguide,
-  Title                    = {MachXO2 sysIO Usage Guide},
-  Author                   = {Lattice~Semiconductor},
-  Month                    = {9},
-  Year                     = {2016},
-  Owner                    = {markus},
-  Timestamp                = {2017.11.25},
-  Url                      = {http://www.latticesemi.com/~/media/LatticeSemi/Documents/ApplicationNotes/MO/MachXO2sysIOUsageGuide.pdf?document_id=39083}
-}

doc/tiny-xo2-documentation.tex

@@ -29,7 +29,7 @@ pdflang=en,
 \usepackage{booktabs}
 \usepackage{multirow}
 \usepackage{graphicx}
-\usepackage{xcolor}
+\usepackage{color}
 \usepackage{pdfpages}
 \usepackage{pdflscape}
 \usepackage[american]{babel}
@@ -44,11 +44,6 @@ bibencoding=utf8
 \addbibresource{lit.bib}
 \DeclareLanguageMapping{american}{american-apa}
 
-\newcommand\Warning{%
-	\makebox[1.4em][c]{%
-		\makebox[0pt][c]{\raisebox{.1em}{\small!}}%
-		\makebox[0pt][c]{\color{red}\Large$\bigtriangleup$}}}%
-
 \usepackage{caption}
 \captionsetup{labelfont=bf}
 
@@ -63,8 +58,6 @@ bibencoding=utf8
 \setlength{\parindent}{0cm}
 \setlength{\parskip}{1em}
 
-\newcommand{\hwmod}[1]{\paragraph{\Warning Hardware Modification \Warning} #1}
-
 \begin{document}
 
 \maketitle
@@ -79,7 +72,6 @@ The Tiny-XO2 is a small, versatile and cost-effective development platform for t
 
 In addition to the \ac{fpga}, it provides a \ac{usb} to \ac{uart} converter and a crystal to include the basic set of components for any \ac{fpga} design.
 
-This manual applies to hardware revision 01.
 
 \chapter{Hardware}
 This chapter explains all available hardware functions.
@@ -119,9 +111,7 @@ The board can be powered either via \ac{usb} or using the \texttt{VB} pin on pin
 
 The \texttt{3V} pins on the pin headers can be used to supply the on-board generated 3.3 V to supporting circuitry. The maximum current to be drawn from these pins is 500 mA\footnote{The maximum current of the AP1117 voltage regulator is 800 mA\parencite[page 4]{tlv1117}. Watch the temperature of \texttt{U1} when drawing high amounts of current.}.
 
-All \ac{io} pins on header \texttt{J3} use the voltage on pin \texttt{VX} as bank voltage. It may range from 1.2 V to 3.3 V \parencite[page 8]{ioguide}. By populating \texttt{R9} with a zero Ohm resistor, the bank can be connected to the on-board 3.3 V supply. In this case, \texttt{VX} becomes a normal \texttt{3V} pin. See chapter \ref{ioheaders} for more details.
+All \ac{io} pins on header \texttt{J3} use the voltage on pin \texttt{VX} as bank voltage. By populating \texttt{R9} with a zero Ohm resistor, the bank can be connected to the on-board 3.3 V supply. In this case, \texttt{VX} becomes a normal \texttt{3V} pin. See chapter \ref{ioheaders} for more details.
-
-\hwmod{If a 2.5 V supply voltage is required for all \ac{io} pins, the main voltage regulator \texttt{U1} can be replaced with a 1117-2.5 2.5 V voltage regulator. The \ac{fpga} will continue to function normally in this case. When doing this, all \texttt{3V} pins carry 2.5 V. \texttt{VX} may be supplied with up to 3.3 V. \textbf{The CH340G \ac{usb}-to-serial converter will stop working in this configuration}, so it needs to be removed from the board.}
 
 \section{\acs{fpga}}
 \label{fpga}
@@ -169,10 +159,6 @@ Additionally, the \ac{rx} and \ac{tx} lines have an \ac{led} connected in parall
 	\end{tabular}
 \end{table}
 
-\paragraph{Reset on terminal.} By default, the \texttt{DTR} pin is pulled low by the CH340 as soon as the terminal is opened on the PC and remains high while it is closed. This high-to-low transition can be detected using an edge detector inside the \ac{fpga} to generate a reset for the rest of the design.
-
-\hwmod{If only a short pulse is desired when the terminal is opened, \texttt{R8} should be exchanged with a 100 nF capacitor and the internal pull-up of the \ac{fpga} must be enabled. Now, each time the terminal is opened on the PC, the DTR line on the \ac{fpga} will go low for a few ms.}
-
 \section{Crystal Oscillator}
 \label{crystal}
 The board features a 12 MHz crystal oscillator. It supplies the clock to the \ac{usb}-to-\ac{uart} converter and is also connected to pin \texttt{28} of the \ac{fpga}. If the 12 MHz clock signal is not needed on the \ac{fpga}, resistor \texttt{R2} can be removed to free pin \texttt{28} as a general purpose \ac{io} pin.
@@ -302,7 +288,6 @@ All \ac{io} pins are available as user \acp{io}.
 	\centering
 	\begin{tabular}{ll} \toprule
 		\textbf{Version}				& \textbf{Comment} \\ \midrule
-		2017-11-25 & DTR usage, 2.5 V mod \\
 		2017-11-20 & Fix \ac{jtag} TDI pin number \\
 		2017-11-16 & Editorial changes \\
 		2017-11-10 & Initial draft \\ \bottomrule