doc: Add errata, change design, extend some paragraphs

This commit is contained in:
Markus Koch 2017-11-27 18:07:27 +01:00
parent 479d1b17b9
commit 0137e1b925
3 changed files with 47 additions and 10 deletions

View File

@ -13,6 +13,7 @@
\acro{fpga} [FPGA] {field-programmable gate array}
\acro{io} [I/O] {input / output}
\acro{jtag} [JTAG] {Joint Test Action Group}
\acro{pll} [PLL] {phase locked loop}
\acro{led} [LED] {light emitting diode}
\acro{ldo} [LDO] {low-dropout regulator}
\acro{rx} [RX] {receive}

Binary file not shown.

View File

@ -30,6 +30,7 @@ pdflang=en,
\usepackage{multirow}
\usepackage{graphicx}
\usepackage{xcolor}
\usepackage{adjustbox}
\usepackage{pdfpages}
\usepackage{pdflscape}
\usepackage[american]{babel}
@ -44,7 +45,12 @@ bibencoding=utf8
\addbibresource{lit.bib}
\DeclareLanguageMapping{american}{american-apa}
\newcommand\Warning{%
\newcommand\hwmodSym{%
\makebox[1.4em][c]{%
\makebox[0pt][c]{\raisebox{.1em}{\small!}}%
\makebox[0pt][c]{\color{blue}\Large$\bigtriangleup$}}}%
\newcommand\WarningSym{%
\makebox[1.4em][c]{%
\makebox[0pt][c]{\raisebox{.1em}{\small!}}%
\makebox[0pt][c]{\color{red}\Large$\bigtriangleup$}}}%
@ -63,7 +69,26 @@ bibencoding=utf8
\setlength{\parindent}{0cm}
\setlength{\parskip}{1em}
\newcommand{\hwmod}[1]{\paragraph{\Warning Hardware Modification \Warning} #1}
\newcommand{\hwmod}[1]{
\begin{center}
\adjustbox{minipage=\textwidth,cfbox=blue}{
\begin{center}
\hwmodSym \textbf{Hardware Modification}\hwmodSym
\end{center}
#1
}
\end{center}
}
\newcommand{\Warning}[1]{
\begin{center}
\adjustbox{minipage=\textwidth,cfbox=red}{
\begin{center}
\WarningSym \textbf{Warning}\WarningSym
\end{center}
#1
}
\end{center}
}
\begin{document}
@ -79,7 +104,7 @@ The Tiny-XO2 is a small, versatile and cost-effective development platform for t
In addition to the \ac{fpga}, it provides a \ac{usb} to \ac{uart} converter and a crystal to include the basic set of components for any \ac{fpga} design.
This manual applies to hardware revision 01.
This manual applies to hardware revision 01. The latest version can be found online at \\ \url{https://l.notsyncing.net/tinyxo2}
\chapter{Hardware}
This chapter explains all available hardware functions.
@ -119,9 +144,9 @@ The board can be powered either via \ac{usb} or using the \texttt{VB} pin on pin
The \texttt{3V} pins on the pin headers can be used to supply the on-board generated 3.3 V to supporting circuitry. The maximum current to be drawn from these pins is 500 mA\footnote{The maximum current of the AP1117 voltage regulator is 800 mA\parencite[page 4]{tlv1117}. Watch the temperature of \texttt{U1} when drawing high amounts of current.}.
All \ac{io} pins on header \texttt{J3} use the voltage on pin \texttt{VX} as bank voltage. It may range from 1.2 V to 3.3 V \parencite[page 8]{ioguide}. By populating \texttt{R9} with a zero Ohm resistor, the bank can be connected to the on-board 3.3 V supply. In this case, \texttt{VX} becomes a normal \texttt{3V} pin. See chapter \ref{ioheaders} for more details.
All \ac{io} pins on header \texttt{J3} use the voltage on pin \texttt{VX} as bank voltage. It may range from 1.2 V to 3.3 V \parencite[page 8]{ioguide}. By populating \texttt{R9} with a zero Ohm resistor, the bank can be connected to the on-board 3.3 V supply. In this case, \texttt{VX} becomes a normal \texttt{3V} pin.
\hwmod{If a 2.5 V supply voltage is required for all \ac{io} pins, the main voltage regulator \texttt{U1} can be replaced with a 1117-2.5 2.5 V voltage regulator. The \ac{fpga} will continue to function normally in this case. When doing this, all \texttt{3V} pins carry 2.5 V. \texttt{VX} may be supplied with up to 3.3 V. \textbf{The CH340G \ac{usb}-to-serial converter will stop working in this configuration}, so it needs to be removed from the board.}
\hwmod{If a 2.5 V supply voltage is required for all \ac{io} pins, the main voltage regulator \texttt{U1} can be replaced with a 1117-2.5 2.5 V voltage regulator. The \ac{fpga} will continue to function normally in this case. When doing this, all \texttt{3V} pins carry 2.5 V. \texttt{VX} may be supplied with up to 3.3 V. \textbf{The CH340G \ac{usb}-to-serial converter will stop working in this configuration} and needs to be removed from the board.}
\section{\acs{fpga}}
\label{fpga}
@ -175,16 +200,20 @@ Additionally, the \ac{rx} and \ac{tx} lines have an \ac{led} connected in parall
\section{Crystal Oscillator}
\label{crystal}
The board features a 12 MHz crystal oscillator. It supplies the clock to the \ac{usb}-to-\ac{uart} converter and is also connected to pin \texttt{28} of the \ac{fpga}. If the 12 MHz clock signal is not needed on the \ac{fpga}, resistor \texttt{R2} can be removed to free pin \texttt{28} as a general purpose \ac{io} pin.
The board features a 12 MHz crystal oscillator. It supplies the clock to the \ac{usb}-to-\ac{uart} converter and is also connected to pin \texttt{28} of the \ac{fpga}. If the 12 MHz clock signal is not needed on the \ac{fpga}, resistor \texttt{R2} can be removed to free pin \texttt{28} as a general purpose \ac{io} pin. A higher frequency for the design can be generated using the \ac{pll} inside the \ac{fpga}.
\hwmod{If another base frequency is required, the crystal oscillator on the back (\texttt{U4}) can be exchanged with another value. \textbf{The CH340G \ac{usb}-to-\ac{uart} coverter will stop working in this configuration} and needs to be removed from the board.}
\section{\acs{io} Headers}
\label{ioheaders}
The \ac{io} headers break out all available \ac{io} pins of the \ac{fpga}. The pin number is marked next to each pin on the board.
Header \texttt{J3} has no special functions and uses \texttt{VX} as bank voltage. This voltage can be tied to the 3.3 V supply of the board by installing a zero ohm resistor for component \texttt{R9}.
Header \texttt{J3} has no special functions and uses \texttt{VX} as bank voltage. This voltage can be tied to the 3.3 V supply of the board either by installing a zero ohm resistor for component \texttt{R9} or by installing a jumper between the \texttt{VX} and \texttt{3V} pin. Refer to chapter \ref{power} for more information on \ac{io} voltages.
Header \texttt{J4} has special functions assigned to most of its pins. Refer to Table \ref{tab:iofunctions} for a comprehensive list. In order to use these pins as general purpose \ac{io} pins, refer to the respective chapter. All \ac{io} pins on header \texttt{J4} use 3.3 V as bank voltage.
Note that the \ac{jtag} pins are connected in parallel to the \ac{jtag} header \texttt{J2} and the corresponding pins on \texttt{J4}.
\begin{table}[h]
\caption{\acs{io} pin special functions}
\label{tab:iofunctions}
@ -276,9 +305,11 @@ Pin \texttt{26} is not available as user \ac{io} in this configuration. Care nee
\subsection{\acs{uart} Bootloader}
\label{progopt:bootloader}
\textit{NYI. TODO.}
The MachXO2 devices can be programmed from the active design. This allows the user to entirely disable all external programming interfaces which makes all \ac{io} pins available to the user logic.
{\color{red}WARNING: Setting these parameters will \textbf{permanently} disable the \ac{jtag} port. This might render the device unusable. Only apply this if you really know what you are doing.}
At the current point in time, this functionality has not been implemented.
\Warning{Setting these parameters will \textbf{permanently} disable the \ac{jtag} port. This might render the device unusable. Only apply this if you really know what you are doing.}
\begin{table}[h]
\caption{Preferences for bootloader mode}
@ -293,6 +324,11 @@ Pin \texttt{26} is not available as user \ac{io} in this configuration. Care nee
All \ac{io} pins are available as user \acp{io}.
\chapter{Errata}
\section*{Hardware Revision 01}
\paragraph{TLV1117-33 decoupling.}
The board is missing the 10+ $\mu F$ capacitor on the output of the 1117-3.3 voltage regulator (\texttt{U1}). This might cause instability with certain devices. This problem can be easily solved by installing a 10 $\mu F$ 0805 capacitor right next to \texttt{C7}. Revision 02 addresses this issue.
\chapter{Appendix}
\section{Version History}
@ -302,7 +338,7 @@ All \ac{io} pins are available as user \acp{io}.
\centering
\begin{tabular}{ll} \toprule
\textbf{Version} & \textbf{Comment} \\ \midrule
2017-11-25 & DTR usage, 2.5 V mod \\
2017-11-27 & DTR usage, 2.5 V mod, errata, editorial changes \\
2017-11-20 & Fix \ac{jtag} TDI pin number \\
2017-11-16 & Editorial changes \\
2017-11-10 & Initial draft \\ \bottomrule